盤扣式腳手架注意事項
盤扣式腳手架品種齊全。盤扣式腳手架配件壓型鋼模板安裝注意事項：需開洞的模板，必須采取相應支撐加固措施后方可切割開洞。開洞后，洞口四周應采取防護措施。開。要經常檢查線路，防止電線損壞漏電。照明、行燈電壓一般不得超過36，潮濕環境不得超過12。遇雨、雪、霜、霧及六級以上大風的天氣時，應停止高空作業。復工前應做清除雨、雪處理。安裝中途停歇時，應對已拆捆未安裝的模板與結構做臨時固定，不得單擺浮擱。每個層段，必須待模板鋪設連接牢固并經檢查合格后，方可進行下道施工工序。已安裝好的壓型鋼板模板，如設計無規定時，施工荷載一般不得超過2.5/，更不得對模板施加沖擊荷載。上、下層連續施工時，支撐系統應設置在同一垂直直線上。吊裝模板的吊具，應采用扁擔式平衡吊具，吊索與模板應呈90夾角。
盤扣式腳手架搭設，高效，盤扣式腳手架立桿采用345級鋼鍛鑄而成，比原有235級鋼具有更高的強度，單根立桿的承載力更大，可達20噸。獨特的盤扣式設計，可使各桿件之間實現多方向穩固連接，滿足腳手架搭設的各種連接要求。與腳手架配套使用的鋼跳板更是比傳統的竹木跳板具有無可比擬的性能。而為盤扣式腳手架量身定做的掛鉤踏步板更是為作業人員在遇到緊急情況下提供了。
